Concrete Slab and Foundation Contractors in Bremen, GA

Build on Concrete Made to Carry the Load

Footings on a west Georgia site have to reach at least 12 inches into undisturbed ground, and the slab above them wants roughly 4 inches of compacted graded aggregate base with a 6-mil vapor retarder between the stone and the concrete. 360 Grading and Concrete pours slabs and foundations throughout Bremen, GA and out across Carrollton, Buchanan, and the rest of Haralson County, covering footing layout, reinforcement placement, vapor barriers, and the finished surface itself.

Red clay holds water long after a storm has passed, so we prove the subgrade before a single truck backs in, compact the pad in lifts, and set forms braced to stay true through the pour. Family-owned, locally owned, and insured, we have spent 7+ years turning raw pads into slabs that framers can start on the following morning. Send your plans or rough dimensions through our contact page and we will walk the site with you.

Concrete Slabs and Foundations We Build

  • Monolithic Slab Foundations

    Footing and floor go down in a single continuous pour, which removes the cold joint where two separate placements meet. Thickened edges carry the wall load while the interior floor stays level, giving a house or shop one uninterrupted structural element underneath it.

  • Footing and Stem Wall Foundations

    Poured footings carry block or poured stem walls, then backfill and a floor slab follow. Sloping lots benefit most, since stem wall height absorbs grade change without stepping the whole structure or trucking in enormous quantities of imported fill material.

  • Garage and Shop Slabs

    Vehicle and equipment loads call for extra thickness, tighter reinforcement, and a broom finish that stays workable when tires track water in. Trench drains, thickened turndowns beneath overhead door tracks, and apron transitions all get planned before forms go up.

  • Subgrade Preparation and Compaction

    Stripping topsoil, proof-rolling the exposed clay, replacing soft pockets, and compacting stone in measured lifts is where slab failures are actually prevented. Density gets checked as the pad rises rather than assumed once the surface looks flat and finished.

  • Rebar and Wire Mesh Reinforcement

    Steel only works where it sits, so bars ride on chairs at the specified depth instead of being hooked up mid pour. Lap lengths, corner bars, and dowel placement follow the drawings, and everything gets tied before concrete arrives on site.

  • Slab Finishing and Curing

    Bull floating, edging, jointing, and troweling each happen in their own window, read from the concrete rather than the clock. Curing compound or wet cure follows immediately, because surface strength is won during the first days and cannot be recovered later.

Why Choose Us for Concrete Slab and Foundation Work

Black verification badge icon with a white checkmark in a circle

Nobody Skips the Pad

The part buried under your slab decides whether it stays flat for decades, and it is also the easiest place to cut a corner. You get a compacted, proof-rolled pad because that is the only way we know how to work.

Black award badge icon with a white checkmark in the center

Forms That Do Not Move

Blown forms mean wavy edges, thin spots, and a slab that never squares up for the framer. Bracing and staking get checked twice before concrete arrives, so what you measured on paper is what you measure afterward with a tape.

Black scalloped badge with a white checkmark inside a circle.

Ready for the Framers on Schedule

Trades stack behind a foundation, and a pad that runs late pushes everybody. We build around your framing date, keep you posted while the pour cures, and hand over a slab that is clean, square, and ready to load.

Black scalloped badge with white checkmark inside a circle on a white background

One Crew from Layout to Finish

Nothing gets subbed out halfway through, so nobody has to relearn your site or blame the previous outfit. The people who shot the grades are the people troweling the surface, and that continuity shows up in the finished floor.

Black checkmark badge icon with a white check inside a circle

Straight Answers Before You Commit

If your ground needs undercutting, extra stone, or a different foundation type than you planned, you hear it during the estimate rather than as a change order. Surprises cost you money, and we would rather lose an argument early.

Black seal icon with a white checkmark inside a circle

Cleanup You Do Not Have to Chase

Washout water, stripped forms, pulled stakes, and offcut lumber all leave the property when we do. A finished pad should look finished rather than like a construction zone you inherited, and neighbors on tight residential lots notice that difference immediately.

Frequently Asked Questions

  • How thick should a concrete slab foundation be?

    Most residential floor slabs land at 4 inches, with thickened edges or turndowns carrying wall loads. Garages, shops, and anything holding equipment usually move to 5 or 6 inches, and engineered plans override the general rule every time.

  • What goes underneath a concrete slab before it is poured?

    Compacted graded aggregate base spreads the load and drains, and a 6-mil vapor retarder sits between that stone and the concrete to block moisture rising from the clay. Plumbing, conduit, and any insulation get placed before either layer closes up.

  • How long does a slab have to cure before framing starts?

    Framing crews commonly load a slab around 7 days, once concrete reaches roughly 70 percent of its design strength. Full strength arrives near 28 days. 360 Grading and Concrete schedules pours around framing dates across Bremen, GA so nobody waits unnecessarily.

  • Does a concrete slab need rebar or wire mesh?

    Reinforcement does not stop concrete from cracking, it holds the crack tight so the slab keeps acting as one piece. Bar size and spacing follow the load, and placement height matters as much as the steel you buy.

  • What is the difference between a monolithic slab and a stem wall foundation?

    A monolithic pour puts footing and floor down together in one placement. A stem wall system pours footings first, builds walls up to grade, then backfills and pours the floor, which suits sloping lots and taller crawl clearances.

  • Why do slabs crack diagonally at the corners?

    Reentrant corners concentrate stress, so shrinkage finds the inside angle of an L shape and travels outward from it. Diagonal bars at those corners and a control joint running off the point are the two usual preventive measures.

  • How deep do foundation footings need to be here?

    Footings bear on undisturbed ground at least 12 inches below finished grade, deeper where soft soil or a sloping lot demands it. Around Bremen, GA, 360 Grading and Concrete digs to bearing capacity rather than frost depth, which stays shallow here.

  • Can concrete be poured in cold or rainy weather?

    Cold slows the set and rain can ruin a fresh surface, but both are workable with planning. Blankets, admixtures, adjusted mix designs, and covered placements all help, and we would rather reschedule a day than finish concrete badly.

Everything You Build Later Rests on This Pour

A slab is the one element nobody can go back and fix cheaply, which is why we spend so much of the schedule below grade where none of it will ever be seen. Getting the stone compacted, the steel supported, and the forms square is unglamorous work that quietly decides whether doors hang plumb in 15 years.

360 Grading and Concrete does that groundwork on every residential, commercial, and light industrial pour around Bremen, GA, and we are happy to explain the reasoning while you are still choosing a contractor. Reach us through the contact page with your drawings, your dimensions, or just a description of the site.